THE BUYING TAKE
Consider the original KMA2685 for repeat offsets from a straight edge after confirming model capacity and saw fit.
The legacy Rip-Cut sets a width on a rail and follows a straight sheet edge. It suits repeat sizing with a compatible circular saw; verify the original 24-inch model and your saw's fit before ordering.
We may earn a commission from these links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Kreg KMA2685
Check current price and availability with the retailer.
Making several strips the same width gives a circular-saw guide a clear job. The Kreg KMA2685 Rip-Cut uses a saw sled, measuring rail and edge guide to keep the chosen offset from a sheet's edge. Its attraction is repeat sizing from a usable reference edge, rather than following a new pencil line for every piece.
This article concerns the legacy KMA2685 shown in the exact product gallery. Kreg's US support page identifies that model as discontinued and specifies a maximum width of 24 inches. Check the supplied version before buying remaining retail stock; a familiar Rip-Cut name does not settle every specification.
Kreg describes a built-in scale and adjustable cursor, with calibration before setting the cut width. Once set, the guide follows the straight edge of the sheet. That is the first buying reason: a repeated-width arrangement for plywood or similar sheet work.
Think about the project you actually expect to make. Several components sharing a width give this design a more focused purpose than one isolated cut. The setting still needs to be correct, and the saw must remain properly mounted. A scale on an accessory does not independently guarantee that the finished pieces meet your required dimensions.
An existing guide may already handle your occasional cuts well. The Rip-Cut becomes more interesting when repeat offsets are a recurring need and the material presents the kind of edge that its guide can follow.
The exact application image shows the circular saw attached to the sled while the edge guide bears against the sheet. Kreg describes taking the saw to the material rather than moving the material to a stationary saw.
That portability is the second buying reason. A buyer who already has a compatible circular saw may prefer an accessory that works where the sheet is supported. This is a choice of working arrangement, not a claim that the guide duplicates every table-saw or track-saw function.
The accessory supplies neither the saw nor a complete support setup. Kreg's manual requires support for both the workpiece and cutoff and preservation of the saw's guard function. A product photograph illustrates the guide's role; the manual and saw instructions determine the complete arrangement.
The manufacturer describes compatibility with most left- or right-blade circular saws. It excludes worm-drive saws and does not recommend saws with a plastic upper blade guard. The retail listing also stresses that the sled must sit flat and clamp securely.
Most is a meaningful qualifier. Check the actual saw base, housing and guard against the instructions rather than interpreting universal sled as a promise for every saw. If the accessory interferes with guard operation, the fit has not been established.
The edge is another requirement. This design follows a straight reference edge; it does not create that reference from a crooked one. If the task lacks a suitable edge, the buying question changes to a guide arrangement that does not depend on it.
Kreg's exact KMA2685 support page specifies sled adjustment from 1 to 24 inches and cuts up to 24 inches wide. The gallery's rail markings are consistent with that original model. These are the specifications used here.
The current retail headline says 48 inches, which conflicts with the exact legacy-model documentation. Do not use that headline to assume double the original capacity. Confirm the model, included rail and seller's supplied version before placing an order, especially if your project depends on a wider offset.
Consider this legacy guide for repeated widths within its documented range, with a straight reference edge and a confirmed compatible saw. It is a focused accessory for a defined setup. A width requirement outside that range, an unsuitable edge or a saw that cannot mount correctly should change the purchase decision.
We may earn a commission from these links, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.
Kreg KMA2685
Check current price and availability with the retailer.
A 64 mm cutting deck, adjustable thickness and three comb blades suit focused vegetable preparation. Compare the actual produce and blade choices before buying.
Cooks who regularly prepare suitable-width vegetables in slices or fine, medium and coarse strips.
Four interchangeable leg widths and an adjustable support foot make this push block configurable. Check blade clearance and workpiece contact before deciding it suits…
Experienced woodworkers who need configurable push-block contact for varied stock and follow machine-specific procedures.
The Narex 863010 pairs 6, 12, 20 and 26 mm bevel-edge chisels with wooden handles. Consider the actual width coverage and grip layout, while leaving room for edge…
Buyers who need these four metric bench-chisel widths and prefer a traditional oval wooden grip.